-
1 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
2 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
3 Umgebungstemperatur
температура окружающего воздуха
Определенная в предписанных условиях температура воздуха, окружающего весь коммутационный аппарат или предохранитель.
МЭК 60050(441-11-13).
Примечание. Для коммутационных аппаратов или предохранителей, установленных внутри оболочки, — это температура воздуха вне оболочки.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
ambient air temperature
the temperature, determined under prescribed conditions, of the air surrounding the complete switching device or fuse
NOTE – For switching devices or fuses installed inside an enclosure, it is the temperature of the air outside the enclosure.
[IEV number 441-11-13 ]FR
température de l'air ambiant
température déterminée dans des conditions prescrites de l'air qui entoure la totalité de l'appareil de connexion ou du fusible
NOTE – Pour des appareils de connexion ou des fusibles installés à l'intérieur d'une enveloppe, c'est la température de l'air à l'extérieur de l'enveloppe
[IEV number 441-11-13 ]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Umgebungstemperatur
-
4 Umgebungstemperatur
f ambient temperature* * *Um·ge·bungs·tem·pe·ra·turf BAU ambient air temperature* * *Umgebungstemperatur f ambient temperature* * *f.ambient temperature n. -
5 Außentemperatur
f < hlk> ■ outdoor temperature; outside air temperature; outdoor air temperature; outside ambient air temperature; outside temperature -
6 Temperaturerhöhung
повышение температуры
-
[IEV number 151-16-26]EN
temperature rise
difference between the temperature of the part under consideration and a reference temperature
NOTE – The reference temperature may be for example the ambient air temperature or the temperature of a cooling fluid.
[IEV number 151-16-26]FR
échauffement, m
différence entre la température de la partie considérée et une température de référence
NOTE – La température de référence peut être par exemple la température de l'air ambiant ou celle d’un fluide de refroidissement.
[IEV number 151-16-26]EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Temperaturerhöhung
-
7 Außenlufttemperatur
f < hlk> ■ outdoor temperature; outside air temperature; outdoor air temperature; outside ambient air temperature; outside temperature -
8 Umgebungstemperatur, f
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
Немецко-русский словарь нормативно-технической терминологии > Umgebungstemperatur, f
См. также в других словарях:
Ambient air temperature — Surrounding temperature, such as the outdoor air temperature around a building. California Energy Comission. Dictionary of Energy Terms … Energy terms
ambient air temperature — the temperature of the surrounding air … Dictionary of automotive terms
Total air temperature — is a term used generally in aviation. In other applications it is called stagnation temperature. Total air temperature is measured by a specially designed temperature probe mounted on the surface of the aircraft. The probe is designed to bring… … Wikipedia
air temperature — The various types of temperatures include: i. Indicated air temperature (IAT). The uncorrected reading from the free air temperature gauge. ii. Basic air temperature (BAT). The indicated air temperature corrected for instrument error. iii. True… … Aviation dictionary
static air temperature — The temperature at a point at rest relative to the ambient air … Military dictionary
Temperature examination — Taking a patient s temperature is an initial part of a full clinical examination.Core body temperature is normally carefully controlled within a narrow range so that essential enzymatic reactions can occur. Prolonged temperature elevation… … Wikipedia
Air pollution dispersion terminology — describes the words and technical terms that have a special meaning to those who work in the field of air pollution dispersion modeling. Governmental environmental protection agencies (local, state, province and national) of many countries have… … Wikipedia
Air pollution — from World War II production Smog over … Wikipedia
Temperature measurement — using modern scientific thermometers and temperature scales goes back at least as far as the early 18th century, when Gabriel Fahrenheit adapted a thermometer (switching to mercury) and a scale both developed by Ole Christensen Røemer. Fahrenheit … Wikipedia
Air cycle machine — An air cycle machine (ACM) is the refrigeration unit of the environmental control system used in pressurized turbine powered aircraft. Normally an aircraft has two to three of these machines arranged in a system called a pack . The cooling… … Wikipedia
Air conditioning — The term air conditioning refers to the cooling and dehumidification of indoor air for thermal comfort. In a broader sense, the term can refer to any form of cooling, heating, ventilation or disinfection that modifies the condition of air.… … Wikipedia
